SATO CL408e,CL412e,UHF RFID Printer (ThingMagic Kit)

RFID Printer 條碼機,提供列印超高頻射頻標籤列印機種,將 CL408e,CL412e 安裝ThingMagic 模組後,即能列印傳統標籤,亦能讀寫UHF RFID標籤

SATO CL408e/CL412e RFID Printer - UHF

參考其它安裝的 SATO RFID Printer

* HF 13.56MHZ : SATO CL408e RFID 條碼機

* UHF 902~922MHZ : 安裝於 SATO GT408e RFID 條碼機

 

RFID 標籤列印說明 :

恆錩銷售之 RFID 列印模組, 是以裝置元件方式, 安裝在SATO條碼機型 , RFID模組在被安裝之後, SATO 條碼機會在開機後, 初始化RFID裝置模組, 之後使用者再進入條碼機的RFID設定選項, 進行相關 RFID 規格設定 , 例如(標籤協定 Gen2, ISO18000-6b 選擇, 以及讀寫的錯誤狀態設定, 等等)

 

完成設定後, 重新開機, 條碼機即可開始透過支援RFID列印之排版軟體來列印 , 例如(LabelGallery, Bartender, NiceLabel ..等, 或是由本公司獨家設計的 GIN格式, 來列印, 亦或是由使用者自行 撰寫列印指令碼來列印.

 

列印過程 :

條碼機收到列印指令後, 會先寫入RFID標籤, 寫入完成, 才會列印標籤, 一旦寫入異常, 條碼機依據使用者在RFID選項上的設定動作指示

做適當的聲音警示,或是產生錯誤的斜線列印 ==> 到標籤上供肉眼辨識, 或是忽略標籤重試下一張標籤寫入與列印,或是產生Error事件停止列印等等),符合各類系統應用的列印需求.

SATO CL408e/CL412e RFID Printer - UHF ThingMagic Mrcury 4e

ThingMagic Mercury 4e 提供一個 UHF 裝置 RFID RW 的方案, 設計安裝在 SATO CL4xx/e 系列條碼機, 支援多項 RFID 標籤通訊協定及頻段( 902-928 MHz, for FHSS use and certification in the US and Canada), 整合在SATO 條碼機上時, 可同時解決了列印標籤, 寫入RFID 標籤, 甚至是讀取標籤的 工作, 使標籤生產上具備效率, 整合式的設計, 具智慧 的RFID列印處理, (錯誤的彌補列印, 錯誤的輸出記號, 嘗試寫入的計數, 調整RFID模組的功率, ), 使標籤的製造生產, 如行雲流水般的穩定.


Dimensions : 5.5cm x 9cm x 1.5cm

RFID Tag and ProtocolSupport :

  • Host-switched multi-protocol:

  • EPC Global Class 0 (including Symbol and Impinj Class 0+ R/W)

  • EPC Class 1 R/W (64 and 96 bit silicon)

  • EPC Generation 2 R/W*

  • ISO18000-6B R/W

Frequency

902-928 MHz, for FHSS use and certification in the US and Canada

RFID Tag Read and Write Rates

Read/write rate and range is protocol dependent and will vary depending on RF signal strength and other environmental factors.

Antenna Connectors

2 MMCX connectors for two antennas. Unit will tolerate 2:1VSWR without damage, but a VSWR below 1.5:1 will be needed for best performance. Circular polarization is supported.

Module Power Supply

Fixed 5.3 VDC +/- 4% DC supply voltage, average power dependent on duty cycle. Peak power not more than 8.8W. Power supply ripple and noise must be less than 100mV pp, and the host power supply load transient response must support a dI/dT of 500kA/s with less than 100mV over/undershoot.

RF Power Output

RF power output depends on available peak supply current. RF output power is variable in 0.1dB steps from 20dBm to 30dBm. Absolute accuracy of RF output power is +/- 1dB.

Sleep Mode

The module can be put in and out of sleep mode by the host processor.

Host Communication

3.3/5V logic level, async serial according to ThingMagic’s MercuryE Communication Protocol Document. The serial
interface includes the settings 115.2 and 38.4 kbaud, 8,n,1, no flow control.

Firmware

Firmware is upgradeable via serial port. Unit first boots into a write-protected bootloader region, verifies CRC of the full firmware image, waits for a Go (or Firmware Upload) command from the host system, and then runs that firmware image. If a valid image is not found by the bootloader, the bootloader waits for a Firmware Upload per the Communication Protocol Document.

Temperature Operating and Storage

Operating ambient temp range 0C-60C.
Storage temp range better than –40C to +85C.

ESD

10kV to antenna shield conductor. Recommend the use of an antenna that presents a DC short to endure 10kV- this is TBD pending testing.

Regulatory

FCC Class B (digital portion) and 15.247 (FHSS radio): Test commands for type acceptance testing will be provided.

Protocol Support

  ID Read ID Write Data Read Data Write Password Write Lock
EPC Global Class 0(Including Symbol and Impinj Class 0+ R/w ) P P P(0+) P(0+)   P(0+)
EPC Class (V1) P P     P P
EPC UHF Gen2 P P     P P
ISO-18000-6B     P P   P

本頁連結二維條碼

RFID Printer 條碼機,提供列印超高頻射頻標籤列印機種,將 CL408e,CL412e 安裝ThingMagic 模組後,即能列印傳統標籤,亦能讀寫UHF RFID標籤

傳送分享

Home部落格 產品送修代客列印 資產盤點HTZ_行動裝置網頁跳到頁頂

線上文字客服購買/連絡我們關於恆錩(上海)鵬碼

地址: 108 台北市萬華區柳州街70號TEL:(02)2306-8858 |Email: sales@htz.com.twQRCode: 首頁連結